国产精品永久免费,亚洲中文字幕无码中文字,无码视频一区二区三区在线观看,欧美两根一起进3P在线观看,好疼太大了太粗太长了视频,色综合久久久无码网中文,国产午夜无码片在线观看影院,八个少妇沟厕小便漂亮各种大屁股,免费VA人成视频网站全,狠狠综合久久综合88亚洲

<strike id="mcwgu"><input id="mcwgu"></input></strike>
<strike id="mcwgu"><input id="mcwgu"></input></strike>

  • <ul id="mcwgu"></ul>
  • News

    Set production, sales, finishing, research and development of innovation as one of the manufacturing enterprises

    ※ Current Location:Home - News - Industry dynamics

    A brief discussion on casting quality inspection and defect repair

    Release Time:2023-02-13      Number of clicks:214

    Casting quality includes inner quality, outer quality and service quality of casting. Its specific requirements, generally in the parts drawing and related technical documents are clearly stipulated. In order to ensure the quality of casting, every link of casting production, especially after cleaning, should be inspected. Any defective casting, after repair can meet the requirements, do not affect the user should be repaired.


    1. Inspection of casting defects


    1) During the inspection and inspection of appearance defects, observe and find the defects exposed on the appearance of the casting, such as cracks, surface pores and shrinkage holes, and sticky sand; Use measuring tools, templates and working platforms to check whether the size of the casting conforms to the requirements of the drawing, and use various weighing tools to check whether the weight of the casting is within the permissible deviation range.


    2) Surface defect inspection


    ① Fluorescence detection method: the casting is soaked in fluorescent liquid, because of the capillary phenomenon, the fluorescent liquid infiltrates into the shortcomings of the surface of the casting, and then take out the casting and wipe it, and put it under ultraviolet (mercury quartz lamp) irradiation. By using the principle of luminescence of fluorescent liquid irradiated by ultraviolet light, the defects such as surface cracks can be judged.


    (2) Coloring method: The use of liquid infiltration properties, the surface of the casting is coated with a layer of infiltration good coloring liquid (such as kerosene, pigment, etc.), to be liquid into the surface shortcomings, wipe off the surface of the coloring liquid, spray a layer of white zinc and other white display powder, then the residual in the shortcomings of the pores of the coloring agent and be sucked to the surface display powder, showing the shape of the shortcomings.


    3) Internal defect inspection


    (1) X-ray inspection: internal defects of the casting can be found, such as pores, shrinkage holes, cracks, inclusions, etc. Figure 2-10 shows the X-ray examination. For important castings, such as Class I castings used in the defense industry, 100 percent radiographic inspection is generally required. Commonly used rays are: X-rays and g rays. The former is less penetrating but more sensitive than the latter, and these rays can penetrate metal and sensitize the negative. As rays pass through an object, they interact with atoms in the object, and their power is gradually diminished by absorption and scattering. The density of holes and inclusions in castings is much lower than the density of metals. When rays interact with these defects, the attenuation is small, and the ability of the negative is larger than that of the parts without defects. Therefore, the shape of defects can be shown on the negative.


    ②*** inspection: can also find the internal defects of the casting, such as pores, cracks, inclusions, shrinkage and so on. For steel casting, this method can be used to detect a large wall thickness (1000mm). *** The working frequency used for inspection is usually above 1MHz. *** is reflected at the interface as it travels from one medium to another. In particular, as much as 99 percent of the ultrasound is reflected back from the interface when it travels from metal to air. *** inspection is the application of this property to find the internal defects of castings. When the head moves slowly on the casting, if the casting has no defects, only T wave reflected on the detection surface and B wave reflected on the bottom surface will appear on the oscilloscope screen. If there is a defect on a part of the casting, there will be F wave reflected by the defect, as shown in Figure 2-11. The greater the defect, the greater the height of F wave, so as to determine the location and severity of the defect in the casting.


    ③ Pressure test: for high pressure and vacuum castings, such as pump body, valves, etc., pressure test is needed to check whether there are holes in the castings. When testing, there will be a certain pressure of air (or water, oil, etc.) into the sealed cavity of the casting, such as casting through cracks, holes, there will be leakage, so as to find the location of the shortcomings. The test pressure is usually more than 30~50 percent of the working pressure of the casting, which is also a strength assessment of the casting. When the casting is not easy to form a sealed cavity, so that the pressure test cannot be carried out, the density of the casting can be tested by means of kerosene infiltration.




    2. Repair of casting defects


    Casting defects do not mean casting scrap, according to the design requirements of castings, in the case of meet the use, can be repaired to repair. There are three common methods of casting repair: repairing with putty and epoxy resin, patching and infiltration patching.


    1) Repair with putty and epoxy resin: holes and holes found on the parts that are not very important to the casting but have decorative significance can be repaired by preparing putty according to the color of the casting. For cast iron, can use iron powder, water glass and cement preparation; For cast aluminum parts, can use aluminum powder, adhesive preparation; For the defects on the non-machining surface, static surface and non-main position of the casting, as well as the shortcomings of oil leakage in the oil tank and oil pool, epoxy resin adhesive can be used to repair.


    2)** repair: This is a common method of casting repair. Arc welding is mainly used for welding steel casting defects. Generally, it can be welded without preheating, but the important parts of the casting, or the structure is very complex, and more metal needs to be welded. In order to prevent and remove the internal stress, improve the plasticity of surfacing metal and reduce hardness, it is necessary to preheat and annealing before welding. Gas welding is mostly used to repair cast iron and non-ferrous metal castings. Cast iron is brittle, in order to prevent internal stress and cracks during repair welding, it is often necessary to slow preheat to 500~550°C, and slow cooling to 50~100°C after welding. Cast iron with complex shape needs to be annealed at 700~800°C after welding. In order to prevent oxidation, argon arc welding is often used in the repair welding of aluminum magnesium alloy castings, and there are strict requirements on the perfect process, otherwise, there will be shortcomings in the repair welding process.


    3) Infiltration repair welding: infiltration is a new technology to solve the problem of casting leakage. It is a gelatinous infiltrating agent into the pores of the casting, and then make the infiltration agent hardening, and the inner wall of the porosity of the casting into one, so as to achieve the purpose of plugging. The commonly used impregnating agent is water glass type and synthetic resin type two categories. At present, vacuum pressure method is generally used to repair castings. The castings were put into a special cage and then put into the infiltration tank. After vacuum-pumping for 1.5~2min(the pressure is less than 5KPa), the castings were flooded with leaching liquid to make the infiltrating agent penetrate into the defective pores. Then, 0.5~0.7MPa compressed air was injected and the pressure was maintained for 20min to further enhance the infiltration effect. Take out the casting, clean it, and wait for the soaking solution to cure.


    Previous:NO!
    Next:The cause and solution of crack in casting aluminum alloy

    Return list

    NEWS YOU MAY BE INTERESTED IN

    日韩成人大屁股内射喷水| 国产亚洲人成网站在线观看| 一本大道久久东京热无码av| 伊人久久大香线蕉av一区| 六月丁香综合在线视频| 男人下部进女人下部视频| 国产女人好紧好爽| 少妇人妻无码精品视频| 免费a级毛片无码a∨免费软件| 国产又色又爽又黄的| 亚洲av无码国产精品色午夜字幕| 精品国产三级在线观看| 草草浮力地址线路①屁屁影院| 男女肉粗暴进来动态图| 人人妻人人澡人人爽欧美一区九九 | 亚洲中文在线播放一区| 国产成人一区二区三区| 久久久久亚洲精品天堂| 欧美黑人又粗又大又爽免费| 亚洲成AV人片天堂网| 国产99视频精品免费专区| 啊灬啊别停灬用力啊| 国产乱人伦偷精品视频免下载| 蜜桃成人无码区免费视频网站| 高清freexxxx性国产| 亚洲午夜福利在线观看| 无码少妇一区二区三区| 无码人妻精品一区二区三区在线| 国产欧美久久久精品影院| 亚洲avav国产av综合av| 亚洲av中文无码乱人伦在线播放 | 小莹客厅激情46章至50章视频| 亚洲乱码一区二区三区在线观看 | 伊人色综合一区二区三区| 精品一区二区三区在线成人| 少妇高潮太爽了在线视频| 久久国产精品亚洲| 亚洲国产AV无码精品无电影 | 播放久久国产乱子伦精品| 日本美女一区二区三区| 亚洲av成人无码网站…|